A Redmond garage floor you coat once. Certified Penntek polyurea goes down in a single day, lasts up to 5x longer than typical epoxy and carries a limited lifetime warranty from Penntek.
We provide concrete coatings, garage floor coatings & epoxy concrete flooring throughout Woodinville WA, Seattle & the Puget Sound
Concrete Floors & Garage Floor Epoxy / Polyurea / Polyaspartic
Residential & Commercial
Get the Longest-Lifespan & Lowest Cost of Ownership from a Certified Penntek Polyurea Floor
Woodinville WA Concrete Coatings & Epoxy Polyurea Garage Floor Coatings
Most garage floors in Redmond start chipping, yellowing or peeling within a few years. Cascade installs Certified Penntek polyurea in one day with a limited lifetime warranty backed by Penntek, so your floor wipes clean and never needs redoing.
Bare concrete soaks up every drip, and a quick epoxy job tends to lift within a few years. Then you're clearing a packed Redmond garage all over again and paying twice.
Experience the difference of a truly superior concrete coating.
Plenty of people call us after an epoxy floor blistered in year three. As a Certified Penntek Dealer we test every slab first, and six Redmond jobs show the result.
Searching for Epoxy Floor Contractors? Learn how our Polyurea Floor Coatings lead to a longer lifespan & dramatically better durability.
Three reasons Penntek polyurea outlasts typical epoxy, with proof from floors coated right here.
On one local garage the grinder started at 10:29 am and the finished Ash flake floor was photographed at 6:51 pm.
Diamond grinding removes the stained top layer, so years of oil marks don't ghost back through the new flake.
The polyaspartic topcoat is non-porous, so oil, road grime and wet-tire grit wipe up instead of soaking in.
Looking for an epoxy floor contractor near Woodinville WA? Cascade Coatings would be honored to connect and share how a Certified Penntek Polyurea Floor leads to the longest lasting, most durable, and aesthetically pleasing epoxy floor solution.
Our floors won't delaminate, yellow, blister or chip.
Our superior process & product leads to tremendously longer lifespans.
Confidently utilize your space without the risk of chips, peeling or low-durability.
Our systems are harder, less porous and remain pristine for years longer.
Choosing a cheap floor leads to short lifespans.
Good, you found the right people. If your garage has oil stains you can't scrub out, tire tracks, dust that never quits or an old coating peeling in patches, you want the clean, glossy flake floor people call epoxy. We install that look with Certified Penntek polyurea, from Woodinville about six miles north of Redmond.
Quick bit of honesty. We wrote this page so anyone searching "epoxy flooring Redmond" or "concrete coating near me" would land here. So we kept it useful: what fails, what works and six real local floors.
Most typical epoxy grips the surface mechanically and dries hard and brittle. It can't move with a slab, so it cracks along with it. Sun through an open door yellows it. Hot tires after a long drive can pull it up. Then there's the install culture around it: thin prep, a fast roll-on and a warranty that disappears if the installer does. That combination is why so many floors fail in years 3–5.
Redmond adds its own pressure. The city spans the Sammamish River valley and the plateaus above it, with 1970s and 1980s neighborhoods next to new subdivisions (the Redmond overview on Wikipedia covers the growth, and the City of Redmond handles permits). Garages here work hard and fill up fast. Wet months bring grit on every tire, and slabs that look dry often aren't. Our consults in town have read between 3.4% and 5.4% moisture.
Folks in Redmond often call this an epoxy polyurea floor, since the steps match an epoxy job. What sets it apart is the whole package: a proprietary pure polyurea blend sold only to certified dealers, slab prep by highly trained Certified Penntek installers, a limited lifetime warranty backed by the manufacturer and a better product once it's down. On the floor, that shows up in four places:
See it tested on our Penntek demo page.
A garage with years of oil stains read 4.1% in October 2024. On November 7 it was ground and coated in Ash flake, entry step included, between 10:29 am and 6:51 pm. See the oil-stained garage now in Ash. A long tandem bay read 5.4% and was finished in Slate Stone the same fall, shown in the Slate Stone tandem garage.
A slab with dark tire tracks and a crazed surface read 4.3% and became Pebble Beach flake on July 31, 2025, with built-in cabinets left in place. Here's the Pebble Beach garage floor. A remodeled garage that read 3.4% to 4.4% got Domino flake in one day that October, with flake returned up the door jambs, in the Domino remodel garage. Another got Smoke flake up its stem walls over two days, and in April 2026 the crew ground a peeling old coating off a backyard deck and laid Quartzite.
A thin coat over light prep can look fine for a year or two. When it fails, it usually fails in the tire lanes first, then near the door. Fixing it means emptying everything out of the garage, grinding off the old layer and paying for a second floor. A warranty from a crew that's no longer around won't cover any of it. Our post on what to do when an epoxy floor starts peeling walks through the fix if you're already there.
Imagine a spill that wipes up with a paper towel, a floor that still looks freshly installed when the kids learn to drive and a garage you're happy to leave open. That's a floor built for 30–40 years, up to 5x the lifespan of typical epoxy. Neighbors nearby have the same floors, from Kirkland garage floors and Bellevue concrete coatings to epoxy poly garage floors in Sammamish and Woodinville.
A typical Redmond garage floor can be coated in one day. Photo timestamps on one local job show the grinder starting at 10:29 am and the finished Ash floor at 6:51 pm. Stem walls or heavy repairs can add a second day.
Polyurea is the stronger choice for a garage floor that sees moisture, slab movement and hot tires. Penntek's basecoat bonds chemically at over 1,300 PSI and flexes, while typical epoxy is rigid. Read Penntek vs. epoxy for a garage floor for the full comparison.
Grinding removes the stained top layer of concrete, and the flake and topcoat cover the rest. The oil-stained Ash garage shows no marks today. Deep contamination can need extra prep, which we flag at the consult.
Hot tire pickup is when warm tires soften a coating and pull it off the slab, leaving bare patches in the tire lanes. Penntek's polyaspartic topcoat is built to resist hot tire pickup, which is a common failure point for typical epoxy.
Built-in cabinets usually stay. The crew coats up to them and protects them, as on the Pebble Beach floor with its workbench and shelving. Cars and loose items need to be out on install day.
We coat outdoor concrete with the same system, after grinding off any old finish. In Redmond that included a backyard deck coated in Quartzite flake in April 2026. Garages are still most of what we do.
Ready for an epoxy-look floor that lasts in Redmond? Book your free in-home quote or call Nicole and Sheldon at 425-226-6085. We're licensed, bonded and insured, and a Home Depot service provider. Thanks for reading a search page all the way through.
Photos & Portfolio
